Siren of Pearls Underwater Tutorial

ForgottenScraps June 23, 2013 3
Siren of Pearls Underwater Tutorial
Howdy folks!  This is Barbara and I’m here to welcome you back to another underwater tutorial.  This one uses the same steps as the last one, but with a different image, it might give you a different perspective too!  For this project I merged a few images together from the fabulous Make it Crafty store and grabbed one of the gorgeous mermaids to play with… Siren of Pearls.  All the colors and images are listed below in case you wanted to jot those down.

 

 

02SirenOfPearls_UnderwaterTuteFlat

 

Step 1 – On this image, the sun will be shining into the water from the upper left corner and I start coloring the rays using B52.  Sometimes it helps me to put an object at the top corner so the angle of the rays radiate in a natural curvature.  Once the first layer of color is applied then I’ll remove the object and remember to be consistent on the direction of the rays. For each stroke of the marker, I use the side of the brush tip and always start outside the range of the image then drag in the direction of the ray with a quick motion.

 

03SirenOfPearls_UnderwaterTuteStep01

Step 2 – Add darker rays with B93. When coloring an underwater scene like this, I like to start with the ocean background first.  That way I don’t have to worry about being precise and if I make a huge mistake then I can always start over without loosing too much.

 

04SirenOfPearls_UnderwaterTuteStep02

Step 3 – I continued to add rays using B00, B93 and B52 until most of the ocean is colored.  It’s okay if the colors are bleeding into the rest of the image since I can either remove most of the color later with a Blender marker.  Plus having some of the blue in the rest of the image adds an overall underwater feel.

 

Step 4 – Now I change direction of coloring to start from the sea floor and use BG11 and BG15 to color up using the same technique.

 

 

Step 5 & 6 – Continue to darken the lower ocean with BG15 and G85 then blend in with BG11 and G00.  I like to pull the greens from the bottom up into the blues but not all the way to the top.  The darkest part is at the horizon of the image but I also add a little bit of color at each ridge in the seafloor.

 

 

Step 7 – I return back to add just a little more color using the original colors, B00, B93 and B52.

 

Step 8 – In this step I add seaweed much the same way I would color grass on another image; the difference being seaweed is more of a wavy line and a lot taller.  Clusters of seaweed are colored in using YG93, YG97, G85, G82 and G40.

 

Step 9 – At this point I’m able to look at the overall effect of the ocean and usually add a bit more color where I think it’s needed until it’s finished.  For this image, I added a touch of G21 and BG72 then blended a little with BG11.

 

11SirenOfPearls_UnderwaterTuteStep09

Step 10 – I colored the rest of the image using a variety of bright colors.  Since the little fish were mostly colored already from the ocean technique, I used the Blender marker to remove a lot of it before coloring them.  I also brought in a little texture by using dots on the seafloor and the mermaids tail.

 

Step 11 – Once everything is colored, I can go back in with the Blender marker to create bubbles and use a white gel pen to add other highlights.  The pearls in the hair was a technique I learned from Daria (http://daria-pn.blogspot.com/) and loved the effect.

 

Step 12 – The final step is to trim around the image and place it on the card and embellish it.  Since the image takes up most of the card area, I clustered my embellishments in one area and left the rest of the card as-is.  Of course the scene looks great without embellishments too but I wanted to experiment with the Fancy Ribbon Sliders chipboard embellishments.  😀

 

 

Copic Colors:

Sea Floor (B00, B93, B52, BG11, BG15, G85, G21, BG72, G21)

Seaweed (YG93, YG97, G85, G82, G40)

Coral (R02, R05, R08, R29; V12, V15, V17; and Y06, Y18, YR23, YR24)

Fish (FYG1, Y06, Y18, BG57, BG09)

Sea Floor (E51, E53, E55, E57, E59)

Clam Shell (R83, R22, R21, R12, R11, R000)

Mermaid Skin (E31, E30, E21, E00, E000, R12, R11, BV23, E04)

Mermaid Tail (B91, B93, B95, B97, B99)

Mermaid Hair (E71, E74, E77, E79)

Shadows (T3, T4, T5)

Make it Crafty Products:

 

15SirenOfPearls_UnderwaterTuteDetails

by Barbara (http://ForgottenScraps.blogspot.com)

If you have subscribed to view this via email, click HERE to view post.

3 Comments »

  1. Lucine June 24, 2013 at 1:12 am - Reply

    I love how you coloured the water; it is like the Sun is shining through. I will keep this tutorial:-) Really nice effect and a great card too! Thank you for sharing.

  2. Kathy July 13, 2013 at 2:01 pm - Reply

    Fabulous!!! The best toot on sun through water that I’ve seen! Thank you 🙂

  3. Patricia June 6, 2017 at 5:33 am - Reply

    Fantastic!!! Just love what you have created.

Leave A Response »